Injection molding PRODUCT NEWS
All
Injection molding COMPANY NEWS
Injection molding PRODUCT NEWS
Injection molding INDUSTRY NEWS

Injection molding PRODUCT NEWS

Safety Operating Regulations for Injection Molding Machines

Check whether there is any foreign matter in the hopper. No items are allowed to be stored above the hopper. The cover of the hopper should be covered to prevent dust and debris from falling into the hopper.

May 1,2021

Safety Operating Regulations for Injection Molding Machines

Plastic injection molding machine

Plastic injection molding is a molding method of injection and molding. Its equipment is called plastic injection molding machine, or injection molding machine for short. Plastic injection molding machine is the main molding equipment that makes thermoplastic and thermosetting plastics into various plastic products. Ordinary plastic injection molding machine refers to the most widely used horizontal,

Apr 21,2021

Plastic injection molding machine

Plastic molding

The commonly used methods for processing thermoplastics include extrusion, injection molding, calendering, blow molding and thermoforming. The processing of thermosetting plastics generally uses compression molding, transfer molding, and injection molding

Apr 21,2021

Plastic molding

Composition and working principle of injection molding machine

The injection molding machine is a special equipment that combines the thermal processing characteristics of plastics and the principle of metal melting and die casting. The first plunger injection molding machine, it was not until the end of the 1940s that a pre-plasticized screw injection molding machine was developed.

Mar 20,2021

Composition and working principle of injection molding machine

The working principle of the plastic injection molding machine is a dynamic diagram, how the product is produced through the injection machine and the mold

The injection molding machine is a special equipment that combines the thermal processing characteristics of plastics and the principle of metal melting and die casting. The first plunger injection molding machine, it was not until the end of the 1940s that a pre-plasticized screw injection molding machine was developed.

Mar 20,2021

The working principle of the plastic injection molding machine is a dynamic diagram, how the product is produced through the injection machine and the mold

Dry Goods—Avoidance Standards for Injection Mold Design

Mould design is an important part of the development process when considering the production of a new moulding. Some considerations are given below.

Mar 1,2021

Dry Goods—Avoidance Standards for Injection Mold Design

Understand injection molding machine Use injection molding machine

Injection molding is a manufacturing process for mass production of parts.It is most commonly used for mass production of the same parts, usually on a scale of tens of thousands or even millions of times.

Oct 24,2020

Understand injection molding machine Use injection molding machine

What are the basic procedures of edM for injection mold cavity operation?

Material for injection mold (plastic mold steel) is required to have sufficient strength, toughness, heat resistance, wear resistance, and good corrosion resistance, heat treatment hardness must be greater than 42-48HRC, cavity working surface needs to keep the surface roughness unchanged for a long time.Commonly used materials are 45, Tl0, TlOA, 9Mn2V, 3Cr2W8, etc.Therefore its electric discharge machining process basic rules are as follows.

Oct 22,2020

What are the basic procedures of edM for injection mold cavity operation?

Model calculation on repetitious recycling

For example, if the actual recycled material ratio is 30%, substitution method can be made by testing once in recycled material ratio of 50%. However, recycling will be influenced greatly by pulverization shape and water control, so sufficient confirmation is required.

Aug 11,2020

Model calculation on repetitious recycling

Proper recycled material mix rate depends on the recycled material quality, using grade

Proper recycled material mix rate depends on the recycled material quality, using grade, and product's demand characteristics, so cannot be completely defined. Therefore, decision of the limit of the recycled material ratio

should be made after sufficient check has been done.

Aug 11,2020

Proper recycled material mix rate depends on the recycled material quality, using grade

NOVADURAN can be recycled

As stated above, PBT will degrade in physicality by causing hydrolysis if heat history is received without enough drying, so the drying of fractured product need to be well considered when recycling.

Aug 11,2020

NOVADURAN can be recycled

Countermeasure against deformation in box molded product

Generally, warpage towards inside tend to be bigger as the span get longer, and it tend to be bigger on the long side, compared to the short side. Remedying by placing a rib on the inside, or placing a triangle rib on the corner part, is possible.

Aug 11,2020

Countermeasure against deformation in box molded product

Countermeasure against deformation in L-shaped and U-shaped molded product

(1) At the corner part, outside cooling will be faster than the inside, so this shape tend to deform towards the

inside direction.

(2) Remedying by placing the gate on the corner part is sometimes possible if it is GF reinforced grade.

(3) Lightening the corner inside part is effective. Make the recess part round, and do not make the sharp

corner.

Aug 11,2020

Countermeasure against deformation in L-shaped and U-shaped molded product

Countermeasure against deformation in flat plate molded product

This shape will be affected a lot by the shape factor, so countermeasure by the molding condition is generally difficult. There is method that make difference in mold temperature, but it will accompany a hardship in facility aspect and management aspect.

Aug 11,2020

Countermeasure against deformation in flat plate molded product